|
|
|
Who's Online
There currently are 5970 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Great manual, would not have been able to operate my machine without it!!
James Dawson August 18, 2012
;
excellent value & price! Includes everything you need to know about the NN-C777! I would buy this again.
;
Very satisfied! I was searching for several days, but nope; till I discovered your webside and there it was at a very reasonable price. Keep up the good work!
Paul
Flanders
 ;
Generally speaking good copy; a few pages too hard contrast...
Good service and communication.
;
I purchased the unit from a private party and the original owners manual was not available. Having the ability to download it was extremely helpful and clarified operating the equipment immensely. This is a complicated unit and without the manual I would not have been able to maximize it's potential. Thank you.
DTR-4.6.book Page 38 Thursday, September 22, 2005 1:45 PM
First Time Setup�Continued
4
Use the Up and Down [ ]/[ ] buttons to select �a. Unit,� and then use the Left and Right [ ]/[ ] buttons to select: feet: Select if you want to enter distances in feet. Can be set from 1 to 30 feet in 0.5-foot steps. meters: Select if you want to enter distances in meters. Can be set from 0.3 to 9 meters in 0.15-meter steps. Use the Up and Down [ ]/[ ] buttons to select each speaker and then use the Left and Right [ ]/[ ] buttons to specify the distance. Specify the distance from the speaker to your listening position.
2
Use the Up and Down [ ]/[ ] buttons to select �3. Speaker Setup,� and then press [Enter]. The Speaker Setup menu appears.
3
5
Use the Up and Down [ ]/[ ] buttons to select �Level Calibration,� and then press [Enter]. The Level Calibration menu appears and the pink noise test tone is output by the front left speaker.
3-3.Level Calibration -----------------------a.Left b.Center c.Right d.Surround R e.Surround L f.Subwoofer : : : : : : 0dB 0dB 0dB 0dB 0dB 0dB
6 7
Repeat step 5 for all speakers. Press the [Setup] button. Setup closes.
Note: Speakers that you set to No or None on the Speaker Con�g menu (page 36) cannot be adjusted.
4
Use the Up and Down [ ]/[ ] buttons to select each speaker, and use the Left and Right [ ]/[ ] buttons to set the volume. The level can be adjusted from �12 to +12 dB in 1 dB steps (�15 to +12 dB for the subwoofer).
Note: � This procedure can also be performed on the AV receiver by using its [Setup] button, arrow buttons, and [Enter] button.
5
Speaker Level Calibration
With these settings, you can adjust the level of each speaker while listening to the test tone so that the volume of each speaker is the same at the listening position. Note: � The speakers cannot be calibrated while the output of the AV receiver is muted or a pair of headphones is connected.
Repeat step 4 so that the volume of the test tone from each speaker is the same. If you�re using a handheld sound level meter, adjust the level of each speaker so it reads 75 dB SPL at the listening position, measured with C-weighting and slow reading. Press the [Setup] button. Setup closes.
6
1
Press the [Receiver] Remote Mode button, followed by the [Setup] button. The main menu appears onscreen.
Note: � The speaker levels can also be changed by using the dedicated buttons on the remote controller. Press the [Test Tone] button to output the test tone. Use the [CH Sel] button to select each speaker, and use the [Level�] and [Level+] buttons to adjust the level.
38
|
|
|
> |
|
